Spruce up a room or give it an entirely different appearance by figuring out how to change a ceiling light installation all alone. Ceiling apparatuses can shift from crystal fixtures for a conventional lounge area, to another light and fan blend for a family room, or another thorough search in an as-of-late renovated room.
You can set aside cash by introducing a ceiling installation all alone with a couple of devices and a partner.
Regardless of whether you have never endeavored a home-establishment project, you can figure out how to wire a ceiling light by adhering to the directions underneath.
Step1: Switch off the current light.
Turn off the electricity to the ceiling light by flipping the breaker that manages the wiring. After you’ve shut down your breaker, pull out your voltage detector to inspect the wires. If voltage is detected, turn off the main breaker on the circuit switch panel. You’ll need to check for any Voltage next.
Step 2 – Get information about your wires
If the power is off, then you can proceed to the next step. You will need to identify what types of wires are connecting the ceiling light so that you can use them accordingly.
The color code for this step is as follows: Neutral wires are white, hot wires are black, and ground wires are bare copper or green.
For the most part, you will be working with black (hot) wires and white (neutral) wires. However, please keep in mind that there could also be a red wire in the junction box.
Step 3 – Know Your Red Wire
You need to figure out which wire on your ceiling light is your neutral wire and which one is your hot wire. The black and white wires are easy to distinguish from each other.
However, if you’re dealing with gold or tawny-colored ones, your search will end here. Keep an eye out for edges that are straightened, have tiny writing on them, or even have a ridge on the plastic sheath.
If you discover any of these telltale indications, you’ve come upon the hot wire. Remove the sheathing from the lamp wires to expose roughly 1/2 inch of bare wire.
Please be aware that UF-B, NM-B, THHN, or THWN-2 wires are only suited for higher-temperature fixtures.
Step 4 – Inspect the Outlet Box
You must now examine your outlet box. It’s crucial to ensure that the box is properly secured. A ceiling fixture weighing more than fifty pounds must have its own electrical box according to the National Electric Code (NEC).
Step 5 – Remove the Ceiling Light
Take down the old ceiling light using a Phillips screwdriver to unscrew its mounting screws. It will be much easier if you have some assistance, but don’t worry-I’m here for it!
If you can, grab someone to hold the ceiling fixture. Now uncouple and remove any electrical tape from the wires. It’s now time to untwine the fixture cables from the house wiring.
Step 6 – Align your Fixture
When installing light fixtures, make sure you balance the rod and avoid straining your arm. It’s a waste of time to assemble everything onto scaffolding before starting so pre-assemble as much on-site while balancing these rods!
If you want to avoid having to put your ceiling fixture together after you install it, take the time to assemble all the pieces before putting it up.
To do so, line up the canopy with the crossbar. Leave a little screw thread exposed in order for it to pass through the canopy. Secure the length with a lock nut.
To hold the crossbar in place, you’ll need to thread the screws into each of the holes on both sides. If you’re working with a rod, make sure it’s inserted into the center hole of your crossbar.
Step 7 – Connect Your Wires
Connect the wires from the old ceiling fixture to this one in the same way. This is a simple step in which you’ll connect the black wire to black and the white wire to white.
The ground wire is a bare copper wire. It must be connected to the green grounding screw in the crossbar.
Having someone else hold the light fixture in place will allow you to focus only on connecting the wires. Once that’s done, you can tuck them into the electrical box.
Step 8 – Line Up Your Fixture
In order to secure your canopy, find the mounting screws and tighten them. If you take a look at most light fixtures, you’ll notice an opening in the shape of a keyhole.
You’ll need to align the head of the screw with the wider part of the hole. Twist the ceiling light clockwise into its narrower position.
With a screwdriver, align the head of the mounting screw with the hole in your alarm clock, as pictured here. For each screw, turn it until tight for extra security.
You’ll tighten the mounting screws at this stage. Adjust the pole so that your canopy is flush against the ceiling if needed.
Step 9 – Wrap Your Project Up
Remove the glass and put it in your light bulbs. After that, place the globe of your light so you can tighten the set screws on its side. Finally, it’s time to switch the electricity back on, and you’ve officially completed
These were the simple 13 steps to install a ceiling light in your house, make sure you select the right size ceiling light before buying one.
Leave a Reply